JavaScript is required

Operating Instructions of NightPro Bottle Warmer Global|MW06

1. Preparations before operating

The first time you unpack the appliance,carefully remove and diispose of all packing materials. Disassemble and clean all parts before the first use and after every use.

2. Operating instructions

2.1 Warming Guidelines

  1. The speed of warming a bottle or food container depends on the initial temperature of the contents, the size of the bottle/food container,etc.
  2. Always add water to the corresponding water mark before placing the bottle in the warmer. Adding the bottle first and then water will reduce the area covered by warm water,resulting in insufficient heating and an uneven milk temperature.
  3. If the milk is not warm enough after heating, you can place thebottle back in the warm water for 30- 60 seconds without restarting the machine.
  4. If the previous heating temperature does not meet your expectations (too hot or cold),you may adjust the heating duration during the next warming cycle using the "+/-"buttons.

Reference Table

Milk Volume

2oz

3-4oz

5-6oz

7-11oz

Required Water

90ml

120ml

200ml

240ml

In "THAW" mode, add 240ml of water to the water mark for milk bags

 

2.2 Standby Mode

  1. After powering on, the appliance enters standby mode, and the power button will light up in green.
  2. Press the button to switch to a warm light,and the appliance will enter the working interface. The screen, night light, and all buttons will illuminate.
  3. If no action is taken after entering the working interface, the appliance will revert to standby mode after 30 seconds, and will automatically power off after 3 minutes in standby mode.

2.3 Warming Room Temperature / Refrigerated Milk

  1. Add 90-240ml of water. Be sure to add water to the corresponding water mark before placing the bottle inside. 
  2. Place the bottle/bag into the warmer (only one bottle at a time).
  3. Choose the required settings based on the milk volume, bottle material, and initial bottle temperature, then press the power button or wait 15 seconds for the heating program to start automatically. The selected function button will light up with a breathing effect.
  4. After heating is complete, the appliance will emit three beeps and dissplay a 60-minute keep-warm countdown timer.
  5. The appliance has a memory function and will automatically retain the settings from previous use. After replacing the bottle, press the power button twice to start a new heating cycle.

Note：

  • Never heat frozen glass containers to avoid glass breakage.
  • Do not allow liquid to overflow from the appliance.
  • Unplug the power cord when not in use.
  • Before feeding, gently swirl the milk and test a few drops on the inside of your wrist.
  • Remove the bottle promptly to avoid overheating, which can leaad to nutrient loss.

2.4 Food Heating Setting

  1. In standby mode, add 90-240ml of water. 
  2. Place the food container into the warmer (only one container at a time).
  3. Press the food button. The default setting is for glass containers. Select the appropriate settings based on the food quantity, then press the power button to start heating. The screen will display a countdown timer.
  4. After heating is complete, the appliance will automatically keep the food warm for 1 hour.

  5. After the keep-warm period ends, the appliance will autormatically power off.

    Note：Before feeding, always check the food temperature,gently stir, and test a few drops on the inside of your wrist.

2.5 Thawing

  1. In standby mode, add 90-240ml of water. 
  2. Place the bottle into the warmer (only one bottle at a time.Not recommended for glass).
  3. In standby mode, press the to enter into working mode. Select “THAW”，then press to select the desired setting based on the bottle material and milk volume (Not recommended for glass).
  4. Press the to start defrosting. The countdown timer will be displayed.
  5. The bottle warmer beeps 3 times and display a 60-minutekeep-warm countdown timer.
  6. After the keep-warm period ends, the appliance will automatically power off.

2.6 24-Hour Scheduled Heating

Description: This function heats the water in the bottle warmer to 37°C-40°C (98°F-104°F), then maintains it at a constant temperature. Place the bottle/bag/food container in the warmer for a period of time before starting, allowing the milk, water, or food inside to reach approximately 37°C/98°F.

  • Preparation for Warm Milk/Formula/Food: Before starting the heating process, it is recommended to set the heating time based on the initial temperature of the milk or food. For room temperature milk/food, set the time to less than 1 hour. For refrigerated milk/food,set the time to less than 2 hours. For frozen milk/food, set the time to less than 3 hours.
  • Preparing Warm Water (for making powdered formula): There is no time limit, and the maximum heating time can be set to 24 hours.
  • Add 90-240ml of water. 
  • Place the container in the bottle warmer (only one container at atime)
  • Press the 24H button (bottle material and capacity cannot be selectted). Press the +/- buttons to select the desired preheating time, then press the power button to start heating.The screen will show the countdown timer.
  • When the time is less than 1 hour, each time you press +/-, the time increses or decreases by 0.5 minutes (long press for quick adjustment)
  • When the time is 1 hour or more, each time you press +/-, the time increases or decreases by 1 hour (long press for quick adjustment)
  • If no action is taken, heating will start automatically after 15 seconds.
  • The countdown cannot be adjusted once it is below 0.5 minutes. Otheer time periods can be freely adjusted.

   4. After heating is complete, the appliance will automatically power off.